- What’s equivalent to a 15 mm socket?
- Is a 3/8 socket the same as a 10mm?
- What are SAE sizes?
- What size is smaller than 11 16?
- What size is 11/16 in MM?
- Is 21mm the same as 13 16?
- What is smaller than a 7/16 wrench?
- Is 5mm the same as 3 16?
- How many 16ths are in one inch?
- Where is 5/16 of an inch on a ruler?
- How do I know what size socket I need?
- What is the smallest measurement on a ruler?
- What are the socket sizes in order?
- What drill bit is closest to 5 16?
- Is 24mm and 15 16 the same?
- What size drill bit do I need for a 5/16 tap?
- What is equivalent to a 15 mm wrench?
- What is bigger 5/8ths or 1 2?
- What is the next size down from 7 16?
- Whats bigger 7/16 or 1/2 inch?
- How big is a 5/16 drill bit?

## What’s equivalent to a 15 mm socket?

SAE to Metric Conversion ChartSAEMetricInch15mm0.59119/32″0.5945/8″0.62516mm0.6347 more rows•Apr 29, 2020.

## Is a 3/8 socket the same as a 10mm?

The equivalent imperial size of a 10mm socket is a 3/8 socket.

## What are SAE sizes?

SAE, which stands for the Society of Automotive Engineers, was used as the standard primarily on U.S.-made cars and trucks through the 1970s. SAE sockets are sized in inches and fractions of inches.

## What size is smaller than 11 16?

SAE to Metric Conversion ChartSAE SizeMetric SizeInches Decimal11/16″0.68818mm0.70923/32″0.71919mm0.74847 more rows•Jul 13, 2020

## What size is 11/16 in MM?

Conversion Table inches to mmDimensions — Inches to Metric0.688”11/16”17.48 mm0.750”3/4”19.05 mm0.813”13/16”20.65 mm0.875”7/8”22.23 mm21 more rows

## Is 21mm the same as 13 16?

Bought the non-marring socket and guess what – while 21mm will work, the 13/16″ is the actual size.

## What is smaller than a 7/16 wrench?

Wrench Size Chart for BoltsBolt DiameterWrench Size (Standard)Wrench Size (Metric)1/8″5/16″8mm3/16″3/8″10mm1/4″7/16″11mm5/16″1/2″13mm20 more rows•May 29, 2020

## Is 5mm the same as 3 16?

4mm = 5/32 inch (= a bit over 1/8 inch) 5mm = just over 3/16 inch. 6mm = almost 1/4 inch. … 9mm = almost 3/8 inch.

## How many 16ths are in one inch?

In this case, there are 16 units of smaller quantity (1/16 inch) in one unit of the larger quantity.

## Where is 5/16 of an inch on a ruler?

The very first line on the left hand side of the ruler is the 1/16 of an inch mark. Between 0 and 1 inch, there are marks that denote 1/16, 2/16 (or 1/8), 3/16, 4/16 (or 1/4), 5/16, 6/16 (or 3/8), 7/16, 8/16 (or 1/2), 9/16, 10/16 (or 5/8), 11/16, 12/16 (3/4), 13/16, 14/16 (or 7/8), 15/16, 16/16 (or 1) of an inch.

## How do I know what size socket I need?

How to Determine the Right Size Socket for a NutTurn on the digital caliper and set it to read in inches, not millimeters. Set the nut on a flat surface. … Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides.Check the caliper display. The reading shows the size of the nut as a decimal.

## What is the smallest measurement on a ruler?

millimetersMetric Rulers Take a look at the following Metric Ruler. The larger lines with numbers are centimeters, and the smallest lines are millimeters. Since millimeters are 1/10th of a centimeter, if you measure 7 marks after a centimeter, it is 1.7 centimeters long.

## What are the socket sizes in order?

Six Point Standard Sockets (5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16) Six Point Metric Sockets (8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21) Six Point Metric Deep Sockets (8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Hex Bit Standard Sockets (5/32, 3/16, 7/32, 1/4, 5/16, 3/8)

## What drill bit is closest to 5 16?

To Tap This Size Screw Or Bolt:Use This Drill Bit:(Closest Fractional:)8mm-1.00mm7.1mm-5/16-32 NEF9/32″9/32″9mm-1.25mm7.9mm-3/8-16 NC5/16″5/16″44 more rows

## Is 24mm and 15 16 the same?

Not only is 15/16″ basically the same as 24mm, but 1 1/16″ is the same as 27mm.

## What size drill bit do I need for a 5/16 tap?

OBW0549. Looking at the “Tap Drill Chart” section at the bottom, they recommend an “F” drill for a 5/16″-18 fastener. Then, looking up above at the “Decimal Equivalent Chart” section, an “F” drill measures 0.257″, about halfway between 1/4″ and 17/64″.

## What is equivalent to a 15 mm wrench?

Wrench Size And Conversion TableInchesMillimetersSpanner0.5639/16 AF0.59115mm0.6005/16 Wworth; 3/8 BSF0.6255/8 AF65 more rows

## What is bigger 5/8ths or 1 2?

Therefore, 5/8 is greater than 1/2 and the answer to the question “Is 5/8 greater than 1/2?” is yes. Note: When comparing fractions such as 5/8 and 1/2, you could also convert the fractions (if necessary) so they have the same denominator and then compare which numerator is larger.

## What is the next size down from 7 16?

The next size after 00g is 7/16″. The sizes go up by 1 sixteenth of an inch from there, but they’re reduced fractions, so instead of 8/16″, we just say 1/2″. (And you probably thought in school you’d never have any use for learning fractions!)

## Whats bigger 7/16 or 1/2 inch?

7/16 and 1/2 can be written as 7/16 and 8/12, hence 1/2 is bigger than 7/16. 1/2 inch is 8/16 so it is bigger by 1/16.

## How big is a 5/16 drill bit?

Drill Bit Hole DiametersMetric SizeFractional Size10 mm.393719/6411 mm.43315/1612 mm.472421/6477 more rows